45 In 1 Sensor Module Board Kit - Gertech

45 In 1 Sensor Module Board Kit

Arduino > Arduino modules

45 In 1 Sensor Module Board Kit Upgrade Version For Arduino (bought from Banggood.com)

Keyes #	Sensor	Picture	Schematic	URL
[KY-001]	Temperature sensor module		Pin - = connect to Arduino GND Pin (middel) = connect to arduino +5V Pin S = Signal, in this example connect to Arduino Digital port 10 When everything is properly connected, there is a led on the module that blinks when the sensor is read.	18b20 Temperature sensor module
[KY-002]	Vibration switch module		Pin - = GND, connect to GND of the Arduino Pin (middel pin) +5 v, connect to Arduino +5 Pin S signal, connect to Arduino pin 10 When there is vibration the Arduino LED on pin 13 flashes.	Vibration switch module
[KY-003]	Hall magnetic sensor module		Pin - = GND, connect to GND of the Arduino Pin (middle pin) +5 v, connect to Arduino +5 Pin S signal, connect to Arduino pin 10 Power consumption, 3 mA in rest, 8 mA when switched on	Hall magnetic sensor module
[KY-004]	Key switch module		Pin - = GND, connect to GND of the Arduino Pin (middel pin) +5 v, connect to Arduino +5 Pin S signal, connect to Arduino pin 10	Key switch module
[KY-005]	Infrared emission sensor module			Infrared emission sensor module
[KY-006]	Small passive buzzer module		Arduino digital pin 8 --> pin 'S' of module Arduino GND --> Pin '-' of module	Small passive buzzer module
[KY-008]	Laser head sensor module		Pin - = GND Pin (middle pin) = not connected Pin S = +5V	Laser head sensor module
[KY-009]	RGB LED SMD module		Since you can't connect the led's directly to the Arduino you will need resistors!! Arduino pin 9 --> 180 Ohm resistor --> Pin 'R' of KY-009 module Arduino pin 10 --> 100 Ohm resistor --> Pin 'G' of KY-009 module Arduino pin 11 --> 100 Ohm resistor --> Pin 'B' of KY-009 module Arduino GND --> pin '-' of KY-009 module	RGB LED SMD module
[KY-010]	Optical breaking		Left = Ground Middle = +5V Right = Signal Connect the module to the arduino as follows: Arduino pin GND to module GND Arduino digital pin 3 to module Signal Arduino pin 5V to module 5V	Optical breaking module
[KY-011]	Two-color LED module		Arduino pin 10 --> resistor 330 Ohm --> Signal pin of the module Arduino pin 11 --> resistor 330 Ohm --> Middel pin of the module Arduino GND --> module -/GND	Two-color LED module
[KY-12]	Active buzzer module		Module pin - = GND Module pin S = +5V Connection to Arduino Arduino digital pin 8 --> Module pin S Arduino GND --> Module pin -	Active buzzer module
[KY-013]	Temperature sensor module		Arduino pin analoog A5 --> module S (Signal) Arduino pin GND - module - Arduino pin 5+ --> middel pin 5V This code don't give the right values, in a room that was kind of ok it gave a tempature of 10 C. That isn't right so the calculation in the code should be checked. Temperature sensor module KY-013 These modules are the same, they're all on boards labelled "S1". THE PINS ARE MARKED BACKWARDS ON THESE. Has pin 1 (marked S) (GND), pin 2 (5v power) and pin 3 (marked -) (analog signal.)??	Temperature sensor module Temperature sensor module
[KY-015]	Temperature and humidity sensor module (humiture sensor Module)		Arduino pin 8 --> Pin S module Arduino GND --> Pin - module Arduino +5 --> Pin Middle	Temperature and humidity sensor module
[KY-016]	3-color LED module		Arduino pin 11 --> Pin R module Arduino pin 10 --> Pin G module Arduino pin 9 --> Pin B module Arduino pin GND --> Pin - module You don't need any resistors, these are already included on the module.	3-color LED module
[KY-017]	Mercury opening module		Arduino GND --> Pin - of module Arduino 5+ --> Pin middel of module Arduino 3 --> pin S of module	Mercury opening module
[KY-018]	Photoresistor module		Arduino A5 --> Module Signal (S) Arduino 5V --> Module +5V (Pin2) Arduino GND --> Module GND (-)	Photoresistor module
[KY-019]	5V relay module		Arduino digital pin 10 --> module pin S Arduino GND --> module pin - Arduino +5V --> module pin +	5V relay module
[KY-020]	Tilt switch module			Tilt switch module
[KY-021]	Arduino Mini Reed module		Arduino GND --> Module pin - Arduino +5V --> Module PLUS (middle pin) Arduino Digital pin 3 --> Module S	Mini Reed module
[KY-022]	Infrared sensor receiver module		Arduino GND --> Module pin - Arduino +5V --> Module PLUS (middle pin) Arduino Digital pin 11 --> Module S	Infrared sensor receiver module
[KY-023]	Arduino PS2 Joystick game controller module		Arduino GND --> Module pin - Arduino +5V --> Module pin +5V Arduino Analoog 0 --> Module VRx Arduino Analoog 1 --> Module VRy Arduino Digital --> Resistor??-->Module SW	Joystick game controller module
[KY-024]	Linear magnetic Hall sensor			Linear magnetic Hall sensor
[KY-025]	Large reed module			Large reed module
[KY-026]	Flame sensor module		Arduino GND --> Module G Arduino +5V --> Module + Arduino digital 4 --> Module D0 Arduino A3 --> Module A0	Flame sensor module
[KY-027]	Magic Light Cup module			Magic Light Cup module
[KY-028]	Digital temperature sensor module			Digital temperature sensor module
[KY-029]	Bicolor LED common cathode module 3MM			Bicolor LED common cathode module
[KY-031]	ARDUINO hit sensor module			Knock sensor module
[KY-032]	Smart car avoid obstacle sensor infrared sensor photoelectric switch			Infrared obstacle avoidance sensor
[KY-033]	Hunt sensor module			Hunt sensor module
[KY-034]	Automatically flashing LED module			Automatically flashing LED module
[KY-035]	Analog Hall magnetic sensor		Pin - = GND, connect to GND of the Arduino Pin (middle pin) +5 V, connect to Arduino +5 V Pin S signal, connect to Arduino pin A5 Power consumption sensor, 8 mA	Analog Hall magnetic sensor
[KY-036]	Metal touch sensor module			Metal touch sensor module
[KY-037]	Microphone sensitivity sensor module		Pin + to Arduino 5+ Pin - to Arduino - Pin A0 to Arduino A0 (for analog program) Pin D0 to Arduino 13 (for digital program)	Microphone sensitivity sensor module
[KY-038]	Microphone sound sensor module		Pin + to Arduino 5+ Pin - to Arduino - Pin A0 to Arduino A0 (for analog program) Pin D0 to Arduino 13 (for digital program)	Microphone sound sensor module
[KY-039]	ARDUINO finger detect heartbeat module		Sensor pin S connect to Arduino pin Analoog 0 / A0 Sensor pin + (middle pin) connect to Arduino pin 5+ Sensor pin - connect to Arduino pin GND	Finger detect heartbeat module
[KY-040]	Rotary encoder module			Rotary encoder module
A	Ultrasonic module			Ultrasonic Module Ultasonic module
B	Gyro Module			Gyro Module
C	Water level module			Water level module
D	SD card reader module		The communication between the microcontroller and the SD card uses SPI, which takes place on digital pins 11, 12, and 13 (on most Arduino boards) or 50, 51, and 52 (Arduino Mega)	SD card reader module SD card reader module
E	Soil module		VCC: 3.3V-5V GND: GND DO: digital output interface(0 and 1) AO: analog output interface	Soil module
F	DS1302 clock module			DS1302 clock module
G	MP1584EN buck module		Input voltage: 4.5V~28V Output voltage: 0.8V~20V Output current: 3A (max)	MP1584EN buck module
H	Breadboard power module		Breadboard Power Supply Module Input Voltage : DC 6.5-12V Output Voltage : DC 3.3V 5V Output Current : 700mA(Max)	Breadboard power module

Back to content | Back to main menu